|
 |
| Durable folding enduro rear view mirror. |
| Part# |
Price |
|
| Enduro Mirror - left |
$19.95 |
|
| Enduro Mirror - right |
$19.95 |
|
|
| |
 |
| Part# |
Price |
|
| #22-700 |
$14.95 |
|
|
| |
 |
| Part# |
Price |
|
| #22-500 |
$49.95 |
|
|
| |
| |
Flasher mounting hardware bolts to your top clamp. Screw hole is 8mm in diameter.
Available in 3 different types.
|
| Part# |
Price |
|
#D45-59-901 
(universal) |
$6.95 |
|
#D45-59-902
(fit triple Clamp mounts that bolt from the front. ie. Honda) |
$6.95 |
|
#D45-59-912
(fits triple clamps that bolt from the side. ie. Yamaha, Suzuki) |
$6.95 |
|
|
| |
 |
| Turn Signal mounting brackets for all SuperMoto Tail Light brackets. The 90 degree angle allows them to mount securely under the fender. |
|
|
| |
 |
| Oil pressure switch for brake light. Available in "bolt" or "banjo" type, depending on your machine. |
| Part# |
Price |
|
Banjo D45-71-291 [M10-1.25]
(Japanese - rear brake) |
$14.95 |
|
Banjo D45-71-292 [M10-1.00]
(Euro - rear brake) |
$14.95 |
|
Bolt D45-71-281 [M10-1.25]
(Japanese - front brake) |
$14.95 |
|
Bolt D45-71-282 [M10-1.00]
(Euro - front brake) |
$14.95 |
|
|
| |
 |
| Stock flasher relay is designed to work with standard bulb flashers. When the stock flasher is changed to LED flasher, the stock flasher relay does not work properly because of the difference in power consumption between the stock flasher bulb and the LED flasher. This IC Relay enables LED flashers to work in any configuration. |
Some models need to use this IC relay with the stock IC relay. (RMX250S, DRZ400S/SM etc.)
- Reduced electrical power usage.
- Some skill required for installation.
- One IC relay required for each bike.
- Can not use flasher pilot light and position light when installed XR250.
- If the flasher operates like hazard indicators after installation,
Indicator lamp wiring kit is required(below).
- Works on 12V DC.
|
| Part# |
Price |
|
| D45-69-830 |
$23.95 |
|
|
| |
 |
This kit is required when flasher operates like hazard indicators after the IC relay installation. Place these harnesses in-between the wires from the pilot lamp and the wires from the chassis.
Some models(XR230, KSR110, KLX250, D-TRACKER etc.) requires this kit for proper operation. |
| Part# |
Price |
|
| D45-91-051 |
$7.95 |
|
|
| |
 |
| When standard bulb flasher is replaced by LED flasher, electric consumption becomes low and stock flasher relay does not work correctly. This resistor wire helps stabilize electric power for LED flasher from stock flasher relay. |
- Electric consumption level is the same as with stock flasher.
- Easy installation.
- One resistor for one flasher.
*Some models (XR230, DR250R, DRZ400S/SM etc.) need 2 resistors.
*This harness will produce heat when used. Please install in area where heat is not a problem.
|
| Part# |
Price |
|
| D45-90-710 |
$16.95 |
|
|
| |
